Luxury vinyl plank, or LVP, flooring is certainly the easiest flooring material to cut and may even be the easiest of all building materials to cut. All it takes is a sharp utility knife and, of course, some patience.
LVP is available in a variety of thicknesses, from 1/4″ to 3/8″ thick, and can be cut to any length you desire. It can also be laminated to other materials, such as plywood, to create a custom-fit floor.
Table of Contents
What is the best tool for cutting vinyl floor tiles?
While handsaw is an excellent tool for cutting through vinyl tiles, you will want to look for a saw with fine teeth so that you don’t damage the tile. A hacksaw or finish cut saw is an example. These have relatively fine teeth that will cut through the tile and leave you with a smooth cut.
If you are using a hand saw, make sure the blade is sharpened to a razor sharp edge. This will make it much easier to cut the tiles without damaging the surface. If you use a finishing saw you may need to sharpen the edge of the saw blade to prevent it from dulling.
How do you cut vinyl flooring accurately?
The safest way to cut corners with vinyl flooring is not to slide off with a knife: Use a metal angle, along this you should make the cut with slight counter pressure. The upper layer of the floor will be damaged if you cut out corners.
Should you wear a mask when cutting vinyl plank flooring?
Cutting the laminate flooring outside prevents dust buildup indoors and also prevents others from breathing in sawdust and particulates. Wearing a dust mask when cutting, which should be done anytime wood products are cut, is also a good idea.
Where do I start vinyl flooring?
Start laying the flooring along one wall, working row by row. The vinyl plank flooring has strips to connect it all together. The first row should be laid along the wall. Glue-down vinyl plank flooring requires you to apply the glue to the subfloor before laying down the next row, so be sure to do this before you start laying out the rest of the plank.
Lay the second row of vinyl. This time, you’re going to use the same method as in Step 2, but this time you’ll be using two rows instead of one. Once you’ve laid the vinyl, it’s time to glue it down. You can either use a glue gun or a spray adhesive, depending on what you have on hand.
If you don’t have either of these tools, then you can use your fingers to spread the glue on the underside of each plank, and then apply it with a squeegee.
What do you put under vinyl flooring?
Most vinyl floors don’t need an underlay. If the surface you’re laying on is level and smooth, a well-cushioned vinyl floor shouldn’t be a problem. It’s easy to work with our Luxury Vinyl Click flooring because it’s loose laid and it’s easy to clean.
Do you have to stagger vinyl plank flooring?
The floor has a fluid and uniform look because of the staggered joints. Determine the size of your floor. If you have a 2-by-2-foot floor, you’ll need to determine the number of feet between the bottom and top of each plank, as shown in the diagram below. You’ll also want to measure the distance from one end of one plank to the other. This will give you a rough estimate of how many square feet of floor you will need.
Measure the length of this piece and divide it by 2. Multiply this number by 4 to get the total length. Cut the piece to this length and place it on a flat surface, such as a workbench or countertop, so that it will be flush with the surface you’re working on.
Which side is the tongue on vinyl plank flooring?
They are cut with precision so that they can create a snug, interlocking installation. Start in the left side of the wall you pick with the tongue on the long side of a piece of plywood, and work your way to the right until you reach the other side. Once you are in place, you will need to drill a hole through the center of your tongue.
This hole will be used to attach the two pieces of tongue to each other. Once you have the hole drilled, it’s time to glue the pieces together. I used a glue gun, but you can use any glue you like. It doesn’t matter which one you use, as long as it is the same consistency as the glue that you used for the studs.
If you don’t have glue on hand, I would recommend using a drywall adhesive. Drywall adhesives can be found at your local hardware store for about $1.50. Just be sure to read the directions on how to use them before you apply them to your wall.
