You can perfectly well saw your laminate floorboards with a regular hand saw. Continue to saw after making a short incision. The saw line should be as close to the bearing surface as possible. The decorative side of the panel should be cut up to avoid damaging the surface.
If you want to make your own, you can use a table saw, but you’ll have to be careful not to damage the wood. You can also use an angle grinder to cut the plywood.
Table of Contents
Do I need a table saw for laminate flooring?
If you’re just learning how to cut floors, you don’t need a special saw. You can use a table saw, circular saw, hand saw, or any other type of woodworking tool to cut the planks. The first step is to determine the size of the floor you will be cutting. You can do this by measuring the width of your floor and dividing it by the length.
For example, if you have a 4′ x 8′ floor, then you would divide 4 by 8. This will give you the number of square feet you need for your project. If you want to make a larger floor than 4′, you’ll need to multiply the square footage by a factor of 2.5 or 3.0 to get the total floor area. Once you know the dimensions, it’s time to choose a planer.
The circular model is the easiest to use, as it can be set up in a horizontal or vertical position, and it has a built-in guide that will guide you through the cutting process.
Can I cut laminate with a utility knife?
Flexible, self-adhering materials such as plastic, rubber, and rubber-like materials can be cut with a regular utility knife blade. The blade is made of stainless steel and has a serrated edge. It has an overall length of 4.5 inches and a width of 1.25 inches. The handle is constructed of black plastic.
How do you cut laminate sheet with utility knife?
Align the square along the next cut line when you turn the laminate one-quarter turn. Apply firm pressure two or three times by drawing the knife across the surface. The score line should be shifted to the edge of the table. You should now have a board that looks like the one in the picture below.
How many teeth do I need to cut laminate?
The number of teeth on the diamond-tipped blades is low to reduce the amount of dust that comes from cutting cement. The saw blades used for laminate will have between 80 to 100 teeth for fine, medium, and coarse cutting. Cement-cutting blades are typically made of steel, aluminum, or stainless steel.
The steel blades can have up to 20 to 30 teeth, while the aluminum blades typically have between 10 and 20 teeth. Stainless steel is the most common type of blade used in cement cutting, but it can also be found in a variety of other applications.
Do you cut laminate flooring upside down?
If you use a radial arm saw, circular saw, jigsaw, or table saw, you should see the planks with the good looking side down. It’s not a good idea to use a saw blade with upside-down teeth if it’s made for laminate. If you don’t have a planer, then you’ll have to use a router.
A router is a tool that can be used to cut straight or curved pieces of wood. It’s a bit more expensive than a handplane, but it’s worth it if you want to get the best results from your planing.
Can you cut laminate with a circular saw?
You can use a hand saw to cut through the countertops, but a circular saw makes the job quicker. Because a circular saw can produce jagged edges and chip the laminate, your best bet is to lay the face-side down and cut from the top to the bottom.
If you don’t have the time or patience to do this yourself, a friend or family member can do it for you. You can also use an electric saw to cut the edges of the countertop.
Can you cut laminate with scissors?
If you lack another kind of trimmer, you can definitely use the scissors to trim your laminated documents especially if you used thinner film. Don’t open and close the blades if you do use scissors. This will make your cut easier. Straight edge and craft knife will work just as well.
You can also use a pair of pliers to hold the paper in place while you cut it. You can even use your fingers to help hold it down while cutting. Just be careful not to cut too deep or you’ll end up with a mess.
