To do this, light the candle and then place a tent of aluminum foil over the top. Poke a hole in the top so that smoke can escape. The foil will reflect heat back onto the candle, melting the wax around the edges and not just in the middle.
Make sure it doesn’t get too hot by keeping an eye on it. Once the flame is lit, you’ll need to keep it lit for a few minutes to ensure that the heat is evenly distributed throughout the entire candle.
Table of Contents
Will a tunneling candle fix itself?
If you leave a candle that tunnels by itself, sometimes it will correct and melt the remaining wax, but most of the time it won’t, leaving you with a permanent ring of solid wax around the perimeter of the container. The harder it is to remove the wax, the longer you wait. The best way to do this is to place the candle in a bowl of water and let it soak for a few minutes.
When the water runs clear, pour it into a glass container and place it in the freezer for at least an hour. The wax will solidify and you can remove it with ease. If you don’t have a freezer, you may want to use an ice cube tray, which will allow you to pour the melted wax directly into your container without having to wait for it to melt.
How do you reset a tunneling candle?
You can fix a tunneled candle by wrapping a piece of aluminum foil around the edges and simply letting it burn. Make sure the foil hangs over the built up wax areas, but leave an opening in the center to burn the candle properly. The wax should melt and even out after a couple of hours. If it doesn’t, you’ll need to re-wax the candle.
How does foil fix candle tunneling?
The foil needs to reach over the tunneled wax. The flame can continue to burn if you keep an open center. The aluminum foil allows the flame to stay even and continuously radiate heat, and the foil also helps to retain heat to prevent the wax from melting.
Once you’ve got your foil in place, you’ll need to cut a hole in the center of the tube. This hole will allow the heat from the fire to escape, but it will also allow air to flow through the hole.
To do this, use a pair of needle-nose pliers to pry open the top of your tube, then use your fingers to push the air out. Be careful not to pull too hard, as you don’t want any air trapped inside.
Once you’re done with this step, it’s a good idea to put a piece of duct tape on the bottom so that you won’t have to do it again.
How do you fix a candle that melted unevenly?
When the top layer of wax has melted, simply hold the airflow over the candle and let it cool. If you don’t want to wait for the wax to melt, you can also use a heat gun to heat up a small amount of water in a saucepan.
Once the water is boiling, add the melted wax and stir until it’s completely melted. You can then remove the pan from the heat and allow it to cool for a few minutes before using it again.
Can you microwave a candle?
Yes, you can put candles in the microwave oven but I wouldn’t advise melting wax using this method. Don’t ever try it, it is very dangerous. If you put candles in the microwave, you will most likely cause a fire accident.
A safe way to melt candles in the microwave is to place the candle in a bowl of hot water, then place the bowl on a stove top and heat the water until it’s hot enough to boil the wax.
What causes sink holes in candles?
They vary in size and depth, and have a direct effect on how your candle wick functions. Sinkholes occur naturally from the process of the wax setting up. As wax is heated to melt it into liquid form, it takes up more space as it changes form. This causes a sinkhole to form at the bottom of a candle.
When the candle is placed in the sink hole, it will not be able to heat up to the same temperature as the surrounding air. The candle will continue to burn at a lower temperature than it would have if it had been placed directly on the surface.
When this happens, a small amount of wax will be left behind, which can be used to fill the hole with more wax if you wish to do so. If you do not want to use this wax, you can simply leave it in place and wait for it to cool down before filling it back in.
