The tongue on laminate flooring is the small flat edge on one side of the board, this is the top edge that is going to angle and lock into the bottom edge. The tongue is made up of two pieces of wood that are glued together. When the glue dries, it will stick to the wood and hold it in place.
You can see in the photo above that the first piece of glue has dried and the second piece has not yet dried. It is important to make sure that both pieces are dry before you glue them together, otherwise they will not be able to hold their shape and will fall out of place when you try to put them back together again.
Now that you know how to glue a tongue, let’s get started on the rest of this project.
Table of Contents
Does TrafficMASTER flooring need to acclimate?
The packaged flooring needs to be placed in the room for a minimum of 24 hours before installation to acclimate it to the room temperature.
How do I cut my TrafficMaster allure floor?
Trafficmaster Allure vinyl flooring does not require much effort to cut the pieces to the length you need. Score a line across the piece, then fold it in half. You’re ready to go because it snaps into two new pieces.
Which end of laminate flooring goes against the wall?
As you start to move your tongue up and down, you want to place the tongue against the wall. Once you are comfortable with this position, you can move on to the next position.
Do you have to cut the tongue of the first row of laminate?
To allow for expansion, place the first plank with the tongue side towards the wall. We recommend cutting off the tongue on this first row to make it easier to work with. Next, place the second plank in the same position, but this time placing it on the opposite wall. This time, you’ll want to cut off all of the excess tongue, leaving you with just enough tongue for the next row.
Once you’ve done that, move on to the third plank, and so on, until you have a total of four rows of tongue. Cut the Tongue . The next step is to take the remaining tongue and cut it off. To do this, we recommend using a pair of scissors or a razor blade. If you don’t have one of these handy, then you can use a sharp knife or even a knife with a serrated edge.
Either way, make sure that the knife is clean and sharp, as you will be using it a lot during the rest of this project. You’ll also need to be careful not to damage the skin on your tongue during this process. It’s a good idea to wear gloves when you’re working with this material, so that you won’t accidentally cut yourself while cutting.
Does it matter which direction you lay laminate flooring?
The direction of your flooring boards has a huge impact on a room’s overall appearance and can be a tough nut to crack. It is a general rule to lay your floor in the same direction as the main light source in the room and the same line as the ceiling.
This will ensure that the light is evenly distributed throughout the room. If you have a large room, you may find that you need to use more than one type of light.
For example, if you are using two different types of lights in your bedroom, it may be best to have one light on the left side of the bed and the other light off to the right. You may also find it helpful to place the lights so that they are facing the opposite direction from each other.
If you do this, your room will look much more natural.
What happens if I don’t acclimate laminate flooring?
If you don’t acclimate your flooring, it will keep adjusting to the local temperature and humidity once it’s installed. This can lead to mold and mildew growth. The first few days are the most difficult, but once you get the hang of it, you will be amazed at how quickly you can adapt to the new environment.
Can you walk on laminate flooring after installation?
Do not walk on the floor for 24 hours after installation. It will cause an unrepairable floor if you do that.
Should I glue laminate flooring joints?
It’s still a widespread installation method even though it isn’t always necessary. Glue is used to ensure your flooring remains durable. It’s less likely that the plank will rise from the floor because it’s glued directly to the subfloor.
Do you need to caulk laminate flooring?
It’s a good idea to apply caulk to fill any holes, imperfections or gaps in laminate flooring. If you have a lot of gaps, you may want to use a caulking gun to seal up the gaps. You can also apply a thin coat of sealer to the edges of the gap to prevent water from seeping in.
Is it better to glue or float vinyl plank flooring?
If you are laying floors in a large area, a glue down flooring application can be used. Glue-down applications are appropriate for smaller rooms as well.