The rule of thumb is to place your light fixture between 1.5 feet and 3 feet from the wall if you plan to illuminate an entire wall or accent particular architectural features. The fixture should be placed closer to the wall if they are fixed.
If your fixture is not attached to a wall, you will need to make sure that it is at least 2 feet away from any wall edges or corners. This will ensure that the light does not reflect off of the walls and into your living space.
Table of Contents
How do you calculate how many recessed lights are needed?
total sq. footage x 1.5 equals total wattage needed. I want to use 6.8 watt bulbs in the room, so I’d like to divide it by 60. Determine how much wattages you’ll need for each type of can light. For example, if I want to install a 60-watt bulb in a 120-square-foot room, I need to calculate how many watts it will take to light the 120 square feet of space.
I’ll then multiply that number by the total square footage of the room to figure out the number of watts needed for the bulb. This is a rough estimate, but it should give you a good idea of what you should expect to pay for your can lighting.
Do recessed lights need to be evenly spaced?
If more than one light is needed, the lights should be aligned. To hide the source of the light, use trims that are adjusted. If you are using a dimmer switch, make sure that it is set to the lowest setting possible. This will allow you to adjust the brightness of your lights without having to turn the switch on and off every time you turn it on.
How many recessed lights do I need for a 10×10 room?
A rule of thumb is that you use one light for every 4 to 6 square feet of floor space. If you have a lot of space, you may want to use more than one light.
For example, if your home has a living room, a dining room and a kitchen, then you would use two receded lights for each of those areas. You would then use a third light in the kitchen for the dining area, and so on until you reach the end of the room.
How far apart should 4 recessed lights be?
The lights that are four inches in size should be placed four feet apart. Six-inch lights need to be placed six feet apart. The space between them is determined by the diameter of the lights. For example, if you have a four-foot-diameter light, you should place it six inches from the edge of your table.
If you are using a light fixture that is larger than six-inches in diameter, make sure that the light is positioned so that it does not interfere with the table top. If the fixture is too large, it may be difficult to position the lamp so it is not in the way of other tables and chairs.
Can you have too many recessed lights?
It is often thought that installing recessed lights is a cure all, but they cannot properly wash light upon walls and all dark corners, which would bounce reflective light into the room.
If you use too much light in your room, it may leave it dark and cost you more money in the long run.
How much area does 6 recessed lights cover?
For a 6-inch light, the number is 1.5, which should be multiplied by the ceiling height. The maximum space between each light should not be more than 6 inches if your ceiling is 8 feet tall.
If you want to add more lights, you will need to multiply the total number of lights by a factor of 2 or 3, depending on the size of the room you are adding the lights to.
If you have a large room with a lot of windows, it may be necessary to increase the amount of light by an additional 3 or 4 lights.
How many recessed lights can you put on one switch?
The rating of the circuit breaker controlling the circuit is the main limitation on the number of lights that a single switch can control. Standard lighting with a 15amp breaker can only be controlled by one switch, because each 60- watt bulb draws around 1/2 Amp. If you want to control more than one light at a time, you will need to use two switches.
If you are looking for a switch that will control multiple lights at once, then look no further than the Z-Wave Plus. This switch is designed specifically for this purpose. It has a built-in dimmer switch, so you don’t have to worry about having to turn the switch on and off every time you turn a light on or off. You can also use this switch in conjunction with other switches, such as those that control dimmers, to create a multi-switch system.
How many recessed lights can I put on one circuit?
A 15-amp breaker for a standard lighting circuit would be able to handle 30 of them, because each fixture with a 60- watt bulb draws about 1/2amp. You wouldn’t install that much in a typical home. If you want to install an LED bulb in your home, you’ll need to find a way to connect it to a circuit that can handle it. You can buy inverters online, or you can build one yourself.
