How To Make A Balloon Arch Without Wire? (Detailed Guide)

how to make a balloon arch without wire

A wire base can be found. If you want the arch to be taller or shorter, use wire cutters to cut a long piece of wire. You can also purchase a balloon arch kit from the store, and use the wire as a base for the balloon. Attach the balloons to your arch.

The easiest way to do this is to use a pair of needle nose pliers and a small flat head screwdriver to hold the two balloons in place. If you don’t have these tools, you can buy them at a hardware store or craft store for around $10. Once you have your balloons secured, attach them to one end of the base and the other balloon on the opposite end.

Make sure that both balloons are at the same height, so that when you attach the second balloon, the first balloon will be at least as high as the one you are attaching to. Be careful not to overdo it, or you may end up with an arch that is too high.

Also, be sure to make sure your balloon base is level with the ground, otherwise you will have a difficult time attaching the next balloon to it.

Check out the video below

Can I make a balloon arch the night before?

Unless you treat them with a product called “Hi-Float,” latex balloons will only float for 10 to 12 hours. If it’s an air-filled balloon arch, or a floating arch made of foil balloons, you can create an arch that will float for up to 24 hours. Cut a hole in the center of the balloon. This hole should be about 1/2-inch in diameter.

You can use a drill bit to make the hole, but if you don’t have one, just use your fingers. If you’re using a screwdriver, use it to pry off the top of a balloon, and then use that as a template to cut out your hole. Be careful not to scratch the surface of your balloon when you do this, as you’ll need to do it again later.

Using a pair of scissors, cut a piece of cardboard about 3/4 of an inch thick. The cardboard will be used to hold the balloons in place while you glue them together. Make sure you cut the cardboard so that it will fit snugly into the holes you’ve made in your balloons.

Is it cheaper to make your own balloon arch?

It looks time consuming and can look expensive as you count how many balloons were used. You can make your own balloon arch at home for less than it would cost to get takeout.

How do you secure a balloon to the arch?

Fill in any gaps in the balloon arch with the 5″ balloons and use the double sided glue dots to secure them in place. The easiest way to see one glue dot is by unrolling the glue tape. Pull the tape tight after pressing the exposed glue dot to your chosen location. Repeat this process for the remaining balloons. Once all the balloons have been glued to the arch, you are ready to attach the rest of the fabric.

You will need to cut a piece of fabric that is approximately 1/4″ larger than the size of your balloon. This will allow you to use a larger balloon to cover the entire arch. Cut this piece to size and fold it in half lengthwise. Fold the folded edge over and pin the two halves together at the top and bottom. Pin the bottom edge of this fabric to one side of each balloon, leaving a 1″ gap between them.

Using the same method as above, fold the other side over, pinning it on top, and secure it with a double-sided tape. Place the pin in this gap and press it down firmly with your thumb and forefinger.

How many days in advance can I make a balloon arch?

up to three days before your party, you can make a balloon garlands. You want to use balloons within 2 days of the party if they are new and glossy. Garland is what it is. Balloon garlands are made up of two parts: the balloon and the ribbon. The balloon is made of cotton or polyester and is wrapped around a ribbon of your choice.

You can use any type of ribbon you like, as long as it is long enough to wrap around your balloon. If you don’t have a long ribbon, you will need to cut a piece of fabric to fit around the balloons. Once you have your balloons cut out, it’s time to attach them to each other. To do this, take your ribbon and fold it in half lengthwise.

This will make it easier for you to tie the two balloons together. Then, tie a knot at the end of each balloon, making sure that the knot is not too tight or too loose. When you are done tying the knots, pull the ends of both balloons apart and tie them together with the same knot. Make sure to leave a little space between them so that they do not get caught in the other’s hair or clothes.

How much is a DIY balloon arch?

To get a general idea of pricing, a simple standard size balloon arch for a small party might start at around $50, while a more elaborate arch for a wedding or for corporate events could cost as much as $500.

Rate this post
You May Also Like