If you have a wire stripper, it’s worth it. If you have wires you’re likely to have a high copper content. The most common method is to soak the wires in a solution of sodium hydroxide (NaOH) and water for a few hours. You can also use an alkaline solution, such as citric acid, to kill the bacteria that cause copper rust.
Table of Contents
How do you strip thin wire for scrap?
If you don’t need to cut the copper wire, you should use a razor blade or handheld stripper since it will save you money. You can also use a wire cutter, but it’s a bit more time-consuming. Wire to the Size You Need to Cut It The first step is to determine the size of the copper wires you’ll be working with.
The easiest way to do this is by measuring the length of your wire and dividing it by two. This will give you the number of feet of wire you need for your project. For example, if I’m working on a 1/2-inch diameter wire, I would divide my wire length by 2 to find out how many feet I’ll need.
I want to work with a 3/4 inch diameter, then I’d divide by 3.5 to get the same number. Once you have this number, you can then divide that number by three to figure out the total length you will need, which in this case will be 2 feet. the end result of this process is that you now have a rough estimate of how much wire to buy.
Why do Scrappers cut cords?
It is a material that can be recycled. Most scrap yards pay more for wires that have been stripped, and non- stripped power cords are often discounted by scrap yards so that you can get the most for your money.
Is it worth stripping 12 gauge wire?
The way it is with insulation, that would translate in to $130.00 for your 100lbs of 12-gauge wire, without stripping it. If you were to strip it, your 75lbs of copper would bring you $1.90 per pound $142.50 the difference between stripping and not stripping.
So, if you are going to do this, you need to know how much copper you will need, and what you can expect to pay for it in the long run.
Can you burn the coating off of copper wire?
We would like to make it clear that you should never burn your copper wire to remove insulation. It is harmful to the environment from the fumes, and will affect your copper at a time when you need it the most. We will be more than happy to assist you in any way we can. Thank you for your understanding and cooperation.
How do you peel electrical wires?
How to get rid of the wires. By simply squeezing the handles about 3/4″ from the end of the wire and then twisting it slightly the insulation will be cut free. The insulation should slide off of the wire when the wire strippers are pulled towards it.
If you don’t have a stripper, you can use a small flat head screwdriver to pry the wires apart. You can also use your fingernail to pull them apart if you have to.
Is burnt copper worth less?
(When you burn copper wire, it loses about half its weight, depending on the type of wire.). If you strip the same wire, you would make at least $32. If you want to strip the wire yourself, you will usually get Copper #1, the highest quality, at about $1.50 per foot. If you are going to use a wire stripper, make sure that you use the right wire for the job.
I have found that if I am stripping copper wires, that I should use wire that is about 1/4″ in diameter. I strip a 1″ diameter wire with a 3/8″ strip, then I will end up with about 2/3rds of a foot of copper. This is because the copper is so thin that it is very difficult to get a good grip on it.
The best way to do this is to wrap the strip around a piece of wood or something that will hold it in place, and then use your fingers to pull it out of the wood. You should be able to remove about a quarter of an inch from the end of your strip before you have to start over with the next one.
How do you clean copper after burning it?
Fill a pot with water, then add a cup of white vinegar and a tablespoon of salt. Mix thoroughly until the salt is dissolved. The mild acid produced by the mixture of salt and vinegar can be used as aPreservative. If you want to make your own vinegar, you can buy it at most grocery stores. You can also make it yourself at home with a few simple ingredients.
