What Gauge Wire For Subwoofer? (Read This First!)

We recommend using wires of 12- to 16-gauge in size. They are the same gauge and there will be no audible difference.

Table of Contents

Is 18 gauge wire good for subwoofer?

It’s fine to use 18 gauge wire for speakers in your home or car. If you want to use 18 AWG for your sub, you’ll need to make sure that the wire you’re using is rated for at least that much power. The best way to tell is to look at the gauge on the end of each wire.

The wire with the highest gauge is the one that’s going to get the most power from the amplifier. You can check this by using a multimeter to measure the resistance between the two ends of your wire, and comparing it to the value listed in the manufacturer’s specifications.

What cables do you need for a subwoofer?

If you don’t have an internal amplifier, you will definitely want to connect an amplifier to it. You will need a power supply, an amplifier, and at least one set of red, white, and black cables to do this. If you’re using a sub that has a built-in amp, connect the amp to the sub’s input. If you have a separate amp that you can plug into the input, then connect it to your amp’s output.

For example, if you’ve got a pair of JBL speakers in your living room and you want them to be able to play music from your iPod or iPhone, plug them into your amplifier and then plug the other speakers into their respective inputs. You can also use an external amp like the Behringer UCA202 for this purpose, but it’s a bit more expensive.

Is 18 gauge speaker wire good?

Speaker wire depends on the length of the run to the speaker and the quality of the sound from the speakers. Exotic speaker wires can cost thousands of dollars and give you a little definition in the sound. 18 gauge wire can be used up to 20 feet, according to the manual.

If you are going to use a speaker wire that is more than 20 feet long, you will need to make sure that it is rated for that length. If you do not want to spend a lot of money on speakers wire, then you can use the wire you already have in your home. It will not sound as good, but it will last a long time.

Is Thicker gauge speaker wire better?

Consider how far away the speakers are from your amplifier and A/V receiver when determining which wire gauge to use. A 16-gauge wire is sufficient for short speaker wire runs. For longer speaker wire runs, it is better to use a 24 or 32-ga wire. For more information on wire gauges, see our Wire Gauge Guide.

What gauge wire do I need?

The carrying capacity and amount of current the wire needs to conduct should be considered when determining what gauge wire you need. How many Amps you need to run through the wire gauge is related to it. The gauge can be impacted by the distance you need the wire to travel.

Can speaker wire be too big?

Speaker wires have to be thicker in order to have better sound quality and lower resistance. Depending on the speaker’s impedance and the type of wire used, not every setup needs a thick wire.

For example, a speaker with an impedance of 2 ohms will have a wire with a diameter of 1/2 inch. A speaker that has a 1 ohm impedance will use a 3/8 inch diameter wire. If you want to get the most out of your speaker wire, make sure it’s the right diameter.

What happens if you use too small gauge wire?

The diameter or heaviness of residential wiring is indicated by the AWG or American wire gauge index. The more current the wire can carry, the heavier it is. Electricity meets the load at a lower voltage if the wire is too small for the load.

AWG is measured in millimeters (mm) and is used to measure the length of a wire. For example, a 1/4 inch wire will measure 1 mm in length. A wire with a diameter of 3/8 inch will be 1.5 mm long.

Is 4 gauge or 8 gauge wire bigger?

The rule of thumb is that the bigger the gauge number, the thicker the cable. The method for measuring the thickness of a cable is standardized. The diameter of the wire is measured from the center of one end to the other end. This measurement is then divided by the number of turns of wire used.

For example, a 1/4″ diameter wire will have a diameter that is 1.5 times its length. A 1-1/2″ cable will be 3 times as long as its diameter, and so on. If the diameter is not specified, it is assumed to be the same as the length, which is usually the case.