If you want to install under cabinet lighting as task lighting, you should place the strip lights closer to the middle front edge of the cabinets to expose the countertop to as much light as possible. For accent lighting, you may want to place them closer to the back edge.
Table of Contents
Does under cabinet lighting Go on front or back?
When mounting a fixture under a cabinet, position it to the front. Look toward the back of the house if there is a lens. The fixture should be hidden from your view by the bottom-front rail of the cabinet. For short runs of less than 1/2 inch, a plug-in fixture may be used.
If you are mounting a fixture to a wall, place it so that it is flush with the wall at the top and bottom. You may need to drill a small hole in the bottom of your wall to accommodate your fixture.
How do you layout under cabinet lighting?
Rules of Thumb for Undercabinet Lighting Locate the fixtures at the front of the upper cabinet. To reduce glare from countertops, use lensed fixture and avoid bare light tape. Even light can be provided across the entire counter by using the longest fixture.
Use a fixture with a minimum fixture length of 1.5 feet (0.9 meters) and a maximum fixture height of 2.0 feet or more (1.2 meters). The fixture should be at least 2 inches (5.4 centimeters) above the floor. If you are using a fluorescent fixture, make sure that it is shielded from direct sunlight.
How do you hide under cabinet lighting wires?
One way to do this is by bundling the wiring carefully and compactly into a bundle and then using tie wraps to hold it in place. Being careful not to pierce the wiring and damage it, you can stick it on the underside of the cabinet with a staple.
Another option is to use a wire stripper to strip the insulation from the wires. This will allow you to solder them directly to the board.
If you don’t want to go this route, you can also use the same method as described above, but instead of using a strip of wire, simply cut a piece of 1/4″ copper tubing and solder it to each wire. The tubing should be about 3/8″ in diameter, so you should have enough to cover the entire length of each cable.
Be sure to wrap the tubing tightly around the cable before soldering it, otherwise you’ll end up with a bunch of loose ends.
How far apart should under cabinet puck lights be?
In general, one puck light is needed for every 8–12 in. of cabinet length. The best distribution of light and avoiding dark areas under the cabinets will be provided by this spacing. Incandescent linear lighting can be either a light strip or a linear fixture. Light strips are the most common type of linear light fixture and are available in a wide variety of sizes and shapes.
Linear light fixtures can be mounted on a wall, ceiling, or floor. They can also be installed in the ceiling or on the floor of a room. Linear lighting fixtures come in many different shapes and sizes, but they all have one thing in common: they use a single light source to illuminate the entire cabinet.
The light from the light bulb is directed through the cabinet and into the room, where it illuminates all of the surfaces and furnishings within the space. In addition to providing a uniform light distribution, linear fixtures also have a number of advantages over other types of lighting. For example, they are less expensive to install, require less maintenance, and can last longer than traditional fixtures.
Do LED strip lights need to be plugged in?
Most of the led strips come with a female 2.1mm connection point so that the connection is seamless. Plug in the led strips into your plug-in power supply and you’ll have a working led light.
You can connect the hardwired power strip to your power source using the female connection on the strip. If you’re looking for something a little more advanced, we’ve got you covered. We’ve created a series of tutorials to help you get the most out of your led strip.
Do under cabinet LED lights need a transformer?
When installing low voltage under cabinet lights, you will have to take some special measures. You’ll need a transformer to convert your home’s voltage supply to a much Page 11 11 lower number, and if you plan to use any accessories, like dimmers, they’ll need to be wired in series with the transformer.
If you’re using a dimmer, make sure that it’s not connected to the same circuit as the power supply. If it is, the voltage drop across it will be much higher than it would be if it were a separate circuit.
Also, be sure to check the wiring of any other accessories you may be using, especially if they’re connected in parallel. For example, if there’s a light switch in the ceiling, it may not be possible to turn it on and off with a single circuit, so you’ll want to connect it to two separate circuits.
How do you space a puck light?
We recommend using 1 puck light for every 6-10 inches of cabinet or shelf space. If you have a lot of cabinets and shelves to light, we recommend you use 1-2 light bulbs for each cabinet and shelf. This will give you a total of 4-6 lights per cabinet/shelf, depending on the size of the cabinet. You can also use a single light bulb for all of your cabinets, shelves, and drawers.
How long do puck lights last?
Your light can last 22 years if it is on for 3 hours per day. The lifetime of the lights is one of the main benefits. As they age, the lights slowly dim. LED lights are also much more energy efficient than traditional light bulbs.
A typical LED light bulb uses about 1.5 watts of energy per hour, compared to about 2 watts for a traditional bulb. This means you can save money on your electricity bill by switching to an LED bulb instead of a conventional bulb, and you’ll also be able to enjoy the benefits of LED lighting for years to come.
How much light does a puck light give off?
The output of puck lights can range from 50 to 80 lumens, while someled bulbs are much brighter than that. Puck lights can also be used as a light source for other applications. For example, you can use a puck light to light up a room, or to illuminate an area where you want to be visible from a distance.
